You might think that using diagonal cutters, wire and chain cutters is a no brainer, but there is actually some common sense to apply that goes a long way when using such a tool. For starters, it&#;s obviously a good idea to keep any part of a living thing away from the business end of the tool, but a more nuanced assessment should clue you in to the fact that even using the tool safely and for the intended purpose you can have problems. Used improperly to cut the wrong gauge wire or something it was not designed to cut you can break the tool and/or cause injury to yourself. So make sure you&#;ve chosen the right tool for the job, wear your safety glasses and use the tool properly.
X-Spark contains other products and information you need, so please check it out.
This guide does a great job of summarizing the basic use of your basic diagonal, wire or other cutters. Of course you open the jaws, put the thing to cut in the back of the jaws and squeeze the handles together. Done. The thing is cut. If you have a softer piece of metal you can cut closer to the tips. Unfortunately, no matter how good the tool is, misusing it can lead to the tools breaking, and we&#;ll take a quick look at what this can look like.
A good example is this cutter with a broken tip. This specific tool is made of C70 tool steel and designed to cut copper, hard piano wire, nails, screws, bolts, chains and more. So why did this tool which is designed to cut such tough stuff get a broken tip? Because as the aforementioned cutting guide points out, while this tool can be used to cut nails, a nail should be cut towards the back of the jaws, not the tip. When cutting hard or tough metals, the back of the jaws has more metal and support and a greater amount of pressure to get through the metal, whereas the tip is reserved for thinner or softer metals like copper wire. An excellent demonstration of the proper use of the tools can be found here with a demonstration of the Wiha cutting a nail properly. This is an excellent version of the cutting tool as it features a push button that increases the power of your cut while also reducing the amount of pressure needed. In short, don&#;t use the tip to cut if it&#;s something that&#;s going to be hard to cut.
Here at Haus of Tools we often stress that buying quality tools is the key to success on the job. That&#;s really only half of the story. The other half is using said tool properly. By misusing a tool, even a good quality tool, you not only run the risk of damaging and destroying your tool, you can also run the risk of injury because when tools break pieces of it can injure you or others. By selecting a quality tool and using it correctly you&#;ll be practically ensured of success on the job or around the house.
Diagonal pliers are mainly used to cut redundant leads of wires and parts. They are also commonly used to replace general scissors for cutting insulated bushing and nylon tire wire cards.
The cutting edge of diagonal pliers can be used to cut rubber or plastic insulation for flexible wires. The cutting edge of the pliers can also be used to cut wires. When cutting No.8 galvanized iron wire, the blade should be cut back and forth several times around the surface, and then the wire should be broken only with a gentle pull. It can also be used to cut hard metal wires such as wire and steel wire. Electricians often use specifications such as 150, 175, 200, and 250mm. It can be purchased according to the needs of internal or external work types.
The jaws of the pliers can also be used to tighten or loosen nuts. The correct way to use diagonal pliers is to hold the palm downwards and hold the palm upwards. The palm downward grip method is to hold the grip of the diagonal pliers with the thumb of your right hand and the other four fingers of the right hand, let the blade of the diagonal pliers move forward, and cut the target forcefully.
Want more information on Diagonals Tool? Feel free to contact us.
When using diagonal pliers, make sure that the pliers face down to prevent injury from the cut thread. In addition, flat jaw pliers cannot be used to cut hard objects such as thick steel wires and screws to avoid damage to their jaws. It is strictly forbidden to use flat-nose pliers with damaged plastic covers to cut live wires to avoid electric shock and ensure personal safety.
The person who uses the tool must be familiar with the performance, characteristics, use, storage, and maintenance methods of the tool. The use of pliers is right-handed. Turn the jaws of the pliers inward to control the cutting part of the pliers. Place your little finger between the two grips, press the grip, and open the head of the grip to separate the grip flexibly.
Diagonal pliers blades can be used to cut rubber or plastic insulation for cords. The blade of the pliers can also be used to cut wires and iron wires. When cutting No. 8 galvanized iron wire, use a knife to cut back and forth around the surface several times, and then just gently pull the wire off. Kushiguchi can also be used to cut hard metal wires such as wires and steel wires. Electricians usually have a variety of specifications. It can be purchased according to the needs of internal or external work types. The teeth of the pliers can also be used to tighten or loosen nuts. Diagonal pliers are a kind of small hardware tools, also known as "diagonal pliers". It has the most extensive functions and is an indispensable tool in people's daily life and work.
We are a diagonal pliers supplier. Please feel free to contact us if you are interested in our products.
The company is the world’s best China Tool Sets supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.
Comments
Please Join Us to post.
0